03
Core toolBuilding system

Plan rooms with Floor planner

Plan internal walls, doors and furniture, then choose interior flooring, wall finishes, ceilings and opening trim.

Open the plan in Build

Choose Build > Floor planner, alongside Building, Openings, Dormers and Porch / balcony. The modes share the same saved design. In Norwegian, choose Bygg > Plantegning. Open the app normally; no special address or URL parameter is needed.

Start by setting the building size, floor system and roof in Building. Use the plan’s Wall, Door and Furniture tools to arrange the interior. The preview updates while you work; Generate building > Build now creates or replaces the 3D model.

Choose the level

Level When it is available
Floor 1 The ground floor of the building.
Floor 2 Enable two storeys in Building. It uses the configured upper-floor elevation.
Loft Use a compatible saved attic/A-frame truss with a loft deck. It is not a third full-height storey.

Walls, doors, room names and furniture belong to their selected level. Temporarily disabling an upper floor or loft retains its layout for when that level is enabled again.

On a loft, post guides and low-headroom shading help explain the usable space. Partitions must fit between the posts and below the roof or collar clearance. Automatic wall height uses the lowest available clearance along the wall.

Resize the building and move openings

Drag an exterior wall handle, or enter Width and Length under Building footprint. The main footprint stays rectangular: resizing keeps the opposite side fixed in the preview and adjusts the adjoining walls together. The dimensions apply to every floor and also update Building mode.

A selected saved truss may lock the width. Use Building settings to review the truss choice. Edit extensions in Dormers; their footprints appear in the plan for context.

Click an existing exterior opening and drag it sideways along its wall. Outside-view left offset gives an exact position using the same outside-view reference as Openings. Choose Edit openings to change its width, height or style. Exterior door hinge and inward/outward swing controls are also available in the plan.

Resizing uses the openings’ existing resize anchors. An opening that no longer fits stays visible with a conflict; correct it before generation. Attached partition endpoints follow their exterior hosts, while unconnected contents keep their coordinates. Furniture keeps its physical size.

Read rooms and dimensions

Enclosed rooms receive labels with area and clear spans. Select a label to enter Room name. Areas use internal finished wall faces and exterior core faces, including the exterior wall’s inner lining when Interior finishes is enabled. Clear spans are measured through the room label, so they are not necessarily the maximum width and length of an irregular room.

Doorways retain the logical boundary between rooms. Partial-height partitions occupy space but do not create fully enclosed rooms. Overall building dimensions use the nominal structural datum, rather than finished room faces.

Under Plan presentation, set Cut height, Drawing scale and Show dimensions. Heavy lines show cut walls; finer lines show frames, furniture and door swings. Dashed openings lie above or below the cut. The 1:50 and 1:100 choices adjust drawing presentation; this release does not add a dedicated floor-plan PDF exporter.

Scroll to zoom, use Shift + middle-button drag to pan, and choose Fit plan to recenter. Hold Shift for finer positioning and Escape to cancel a drag. Plan Undo/Redo covers plan edits; editing another designer mode starts a new plan-edit history.

Interior finishes

Check Interior finishes immediately after Furniture. The options open on the left of the plan viewport; Finish options reopens them. Flooring, Wall sheathing and Ceiling start with White seamless, and each also offers None. Choose Done, then Generate building to apply the selections to all active floors and an enabled loft.

  • Flooring: pine, natural oak laminate, ash laminate or oak herringbone, with board/stave dimensions and knot visibility. Board direction selects Along building length or Across building width, including herringbone.
  • Wall sheathing: vertical or horizontal wood panels in light or dark timber, with panel width, joint width, joint visibility and knot controls; paint from the palette or a custom colour; and seven wallpapers with pattern scaling.
  • Ceiling: seamless white, whitewashed pine panels, or Match walls. Ceiling board direction is independent of flooring direction.

Flooring continues through doorways and meets partition finished faces. Exterior wall lining follows window and door cuts; partition finishes retain their thicknesses and connected corners. Low partitions leave the ceiling continuous. Flooring is 5 mm thick, and exterior lining and ceilings are 13 mm thick. Changing textures does not change these dimensions.

Trim and reveals

In Finish options > Trim & reveals, check Add interior trim. Enable reveal boards, face trim, or both, then choose white/custom paint, pine or oak. Controls cover board dimensions, the visible reveal edge and mitred or square heads. Reveal depth follows the frame and finished wall automatically. Windows receive four sides; doors leave the floor passage open. Partition doors receive trim on both faces. Narrow frames limit reveal thickness to keep the opening clear.

After generation, the regular Opening Framer cuts the interior lining for new windows and doors and inherits the building’s trim choices. It also works from inside in perspective with a 2100 mm from floor guide. Glazed facade assemblies retain their existing continuous frames.

The material sample updates while editing. Sliders make one undo step on release; closing the menu keeps the selections. Unchecking Interior finishes keeps choices for later and applies the disabled state on the next generation. New project saves use .strek V72; use a compatible reader and retain an original copy for older app versions.

Generate and save

Follow internal walls and doors for framing settings. Generated partitions, finishes and internal doors appear in the Partition group. Furniture and interior currently stay in the 2D plan; generated 3D support is in development.

Save Drafts & variants for design alternatives, then save a .strek file to retain the project after closing. Save project copy is available in the designer even before first generation. Account building presets do not replace these saved layouts.

The current release supports orthogonal partitions and a rectangular main footprint. Stairs, arbitrary exterior wall polygons and automatic structural sizing are outside its scope. Direct edits to generated 3D parts do not update the designer recipe; save a copy before regeneration replaces those edits.

For drawing sheets from the generated model, use Project Planner. That is separate from arranging rooms in Build’s Floor planner.

Privacy controls

Your choice, clearly stated

Choose which optional cookies Autostrek may use. Essential cookies support account access and security. You can change your preferences at any time.

Read the Privacy Policy